Painting Tips

Painting can either be easy or hard! It's really up to you. It can take you a long time to paint a room or a small amount of time. That, also, is up to you.

1) Cutting the inside corners. Cutting the corner up against another color or at the ceiling can be challenging, especially if your walls are textured. It can be really difficult to get that nice clean and straight transitional cut..... or, it can be easy. Here's what you do: Use painter's blue tape and run it with one edge exactly on the corner. Next, take white painter caulking (the cheapest kind) and run a very fine bead exactly in the corner and smooth it out with you finger. Now cut in your paint along that edge painting over the edge of the tape as well. Before paint dries, pull the tape. Wallah! you have a sharp cut in edge.

2) Don't use cheap paint. But also don't use expensive paint. Use a good premium paint like Valspar, or Behr. But if you are using Behr, don't fall for that expensive stuff with the primer already in it.... you are wasting your money. Their regular paint actually paints up better.

3) Don't try to stretch the paint by using a dry roller. A roller with plenty of paint on it and applied liberally ensures better coverage, a more even paint job, and in the end may take less time and paint. If you use too little paint on your roller I can guarantee a lot of breakthrough.

4) Use a quality roller such as those expensive white ones at Home Depot. They leave less lint on your wall.

5) Use a quality brush and the right brush for the job. The 1.5" and 2" angle brushes work well. I have found nothing that compares to Purdy.

6) Clean up: Purdy brushes are worth saving. Spray a little orange oil on them and let them sit for a few minutes. Now they will easily clean under luke warm water. The roller covers? Throw them. They are actually pretty cheap and a new roller cover will do a better job on your next painting project.

Insulate

Recently I made our ice cold garage a little warmer. Actually it stays above freezing now. What did I do? I insulated.

First, I insulated the metal garage door by stuffing the panels with glass insulation then covering that with a moisture resistant plywood about three-sixteenths of an inch thick. It was actually underlayment for vinyl floors. You can buy it at Home Depot. This was installed with sheet metal screws. Then I adjusted the door opener for more weight.

Then I insulated the garage attic with R-19 unfaced glass insulation which I bought at Home Depot for 22 cents per square foot. I sealed off the ends of the cells between ceiling joists by placing insulation between the joists. After that I laid the insulation across the joists butting it firmly batten to batten. The result was a much warmer garage.

The total cost for materials was $190. Now my garage will serve as a warm shop in the winter and will be much cooler in the summer. I'd say this is a good investment.

Having Toilet Problems?

Are you having toilet problems? Well, let me reword that..... "is your toilet having problems?" Maybe you are getting tired of using that plunger. I hate clogged toilets. How about you?

Ever since government regulations went into effect for water conservation, many of the newer models have had issues flushing. Frustrating! But now there is hope. Many of the newer toilet designs have greatly improved the flush. And, it won't cost you an arm and a leg to replace your old toilet. That is, if you do it yourself. And many of you can do it.

Remove the old toilet. Make sure you turn the water supply valve to off. Then flush to remove water in the tank and in the bowl. Then disconnect the water supply line. Then unbolt the toilet from the floor. Now lift it off and discard. Remove the old wax at the flange where the toilet sits.

Now install a new wax ring before you forget. I like the type with the rubber flange and extra wax. Before you set the toilet bowl on the wax ring, bolt the tank into place and make sure it is firm but not overly tight. Make sure the flange bolts are securely lined up with the slots at the base of the toilet. Now set the bowl on the wax ring so that the bolts come up through the slots. Press the bowl down on the wax ring until the base touches the floor. Now put the base to the bolt cover on, then the washers, then the nut.

Now you are ready to hook up the water supply line. Allow a little water into the tank and check for leaks. If there are no leaks, turn the water on and let the tank fill. Most manufacturers have pre-set the water lever for the tank. Flush. If everything works okay install the tank top.

Now, to finish off the project you may have to trim the tops of the anchor bolts. Score the anchor bolts with a hack saw or side cutters about 1/4 inch above the nuts. Then with a pliers, snap the bolt tops off. Now install the bolt covers.

Don't forget to install the seat! Caulk around the base if you wish.

Wallah! Your project cost you about $150. But you saved about $200. $200 can buy a lot of starbucks!

Have Paint Going to Waste?

Most of us have many cans of paint sitting in storage going to waste. I know, I know! You think you will use it for touch up here and there. But in the end we seldom touch up and the paint spoils. So, now you have to buy hardener to harden the paint so you can dispose of it. I have a partial solution for your extra paint. Paint the interior of your garage!

Sitting in my garage I had a full gallon and a partial gallon of house paint that I had used on other houses. I knew the paint was going to just sit there and take up space until I disposed of it. The colors were mauve and white. The interior of my garage was already white. Dirty white, as in dirt on white. So I decided to clean it up with a fresh coat of paint. That led me to these left overs of paint. I decided that it was only the inside of the garage and that mauve wouldn't be too bad of a color.

Man, you should see the garage now! It looks so good that I feel like leaving the overhead door open so the neighbors can see. Not only did I clean up the garage with paint, but it also forced me to clean up my junk and organize. I guarantee you, it looks nicer than a lot of houses I've been inside of. And guess what? Zero cost.

I feel so good about it I think I'll buy myself a Starbucks! Or, maybe a new car to put in my showroom. Just don't tell Audrey these evil thoughts. Please! :)

Does Your Table Rock?

One of my biggest pet peeves is a table that rocks back and forth. You know, like the ones they have at Starbucks. That is so irritating! But it just happened to be the only table available.... and for a good reason.

Well, there is a simple temporary fix. You can go get enough napkins and fold them over until they are thick enough to stuff under the table leg. I've done that. Or you can carry some small wooden shims in your purse or computer bag. One simple push and your table doesn't rock.

But speaking of rocking tables, these small round tables could be made slightly different and become more stable. Instead of four points of contact, they could have three points. There will be no rocking there. No rocking means less spilt coffee, which means fewer ruined computers. And, there will be more satisfied customers. I think that's what every business wants.

Outside Lights

Do you have outside lights that you like to have on at night but you have to remember to flip the switch? I'll bet most of the time they are never on. To solve this some people have bought those sensors that you screw into the bulb socket. These work most of the time but your light bulb is no longer in the correct position. There is a better way.

Go to Home Depot or another hardware store and buy a sensor for about $12. Also buy an electric gang box with wings for $1.50. Twenty-five feet of 3 strand wire will do it. That would be 12-3 gage wire.

The switch to your exterior light beside the front door should be located in the interior side directly below the exterior light. Remove the exterior light to reveal the wiring. Next, you need to cut a rectangular hole on the exterior side the size of the gang box insert. Now install the gang box making sure it is secure. Fish your wire through from the gang box to the light box and wire it according to the instructions included with the sensor. Re-install your light. Finally, test the sensor by putting black tape over the sensor eye. Turn on the light switch. Wait a couple of minutes. If the light comes on then your sensor works.

Now all you have to do is to remember to leave your light switch on at all times. Let the sensor do the rest.

Fix the Squeaky Floor

Two of the most irritating things I know of are squeaky shoes and a squeaky floor. Fixing squeaky shoes is easy.... discard them. Fixing a squeaking floor is a little more difficult.

There are basically two reasons a floor may squeak. The most common reason is that it was improperly nailed to the joists and over time some of the nailing has worked loose. The squeaking is caused by the floor moving up and down again the nails. Simply tapping the nails down will not fix the squeak, that will be only a temporary fix. A proper and lasting fix will require removing the loose nails then installing new fasteners. The fasteners I prefer are the trapeze type deck screws one and five-eighths inches in length. Whereas other screws actually created separation between the joists and the plywood, these screws actually suck the plywood down tight. That is what eliminates the squeaks.

The other problem causing squeaking is the edges of the plywood rubbing together when they move. This can happen between floor joists as plywood flexes. The fix for this is to us a circular saw and cut along the seam between sheets if plywood to create space. Set the depth of your saw blade for only the thickness of the plywood to prevent cutting into the joists.

There are key times to fix the squeaks. One is when you are changing carpet of floor coverings. At this time the floor decking is open and joists are readily findable. These squeaks must be fixed before installing hardwood or tile. Covering them up will not fix the problem. In fact, your tile may crack if the squeaks are not repaired.

If you have any questions you may contact me in the comments area.